EMULAB Forum
clrmamepro [English] => clrmame Discussion => Topic started by: Roman on 08 December 2009, 22:19
-
3.132
added: basic support for HyperSpin dat files
added: optional warning about archives (zip/rar) with comments (compressor settings)
added: missing/available bytes display in profiler and html report
added: rebuilder advance option to not create set folder when rebuilding to decompressed sets
misc: changed renamewizard keep parent behaviour to "if the old set was a parent and is renamed to a non-parent
in the new dat, you can use the option to allow this or not."
misc: show prompt after renamewizard modified a dat
misc: changed windows rect calculation which may solves weird border issue
misc: some minor code cleanup here and there
fixed: show wrong setname in download popupmenu
fixed: don't mark profile as green when a sysdefpath not assigned message pops up
fixed: separated biosfiles are wrongly counted as missing in fully missing sets
-
ah ok...the missing bytes header also appears in www profiler mode...will be fixed in next version...for 2009, ignore it ;)
-
Not sure what happened but completely dies in wine for version 3.132. Just updated via the internal update function, .exe fails to run. Removed via wine and deleted ~/.wine/drive_c/Program Files/clrmame and re-installed via 32-bit .exe and same problem. winedbg is not working for me for some reason, but otherwise wine with the executable gives no output, just dies.
Wine version is 1.1.32-1.fc12
Was working before update, same version of wine.
-
hmm..nothing that dramatically changed...especially not during startup...weird...maybe it's the UPX packed exe....send me an email and I will send you a decompressed version (or try the 64bit build if possible :))
-
Alright, well not sure what happened on my end (cause I was using cmpro before the update), but a reboot seemed to fix it. (also rebooted into a new kernel but i highly doubt that had anything to do with it).
sorry to waste your time.
-
you're welcome
-
Roman,
I believe I'm experiencing a bug regarding the new option 'warning about archives (zip/rar) with comments'.
When enabled, ALL *.rar files scanned are throwing up comments warnings. When opening in WinRAR there appears no comment, and since I rebuilt them 'clean' from uncompressed folder I'd be very surprised if they did.
I'm using Windows 7 Ultimate x64, WinRAR 3.90 x64, clrmamepro 3.132 x64 (obviously!) with the following compression settings: a -y -r -t -m5- %1 %2
Any ideas?
-
hmm..yeah...bug...will fix this
-
Still doesn't work properly.... :(
-
works fine here with 3.132a. Mail me a rar file where it does not work for your.
-
Just sent you an email.
It doesn't appear to be every RAR archive, since I've also done some other scans today without issue.
One interesting thing to note is that the DAT I had this problem with (and where the RAR I sent you is from) is an existing DAT, whereas the other DAT without issue is an 'updated' DAT....
*.cmp issue maybe..?
-
Just back from holiday...will check your file asap...
-
cmpro 3.132a does not report a comment in your sent rar....and actually it does not have one.
So...you're sure you scanned *that* rar with 3.132a? Got another file?
-
100% sure.
That’s what I’m saying, it obviously doesn’t have a comment in it but that’s what clrmamepro was reporting.
I still suspect it’s a new/existing DAT specific issue.
I’ll dump a zip of my clrmamepro install folder (without all my other DATs, just with this one and possibly some other problem DATs) as well as some more example files (these ones are only small) onto my ftp when I’m back home. I’ll email you the link.
Thanks for looking into this, especially since it would appear I’m isolated/in minority in experiencing this issue.
-
yeah send me your files....the dat is definetly not the case for this.
-
ah forget it.....I found the issue :O)